| Internet Engineering Task Force (IETF) | R. Fielding, Editor |
| Request for Comments: 7230 | Adobe |
| Obsoletes: 2145, 2616 | J. Reschke, Editor |
| Updates: 2817, 2818 | greenbytes |
| Category: Standards Track | June 2014 |
| ISSN: 2070-1721 |
Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing
Abstract
The Hypertext Transfer Protocol (HTTP) is a stateless application-level protocol for distributed, collaborative, hypertext information systems. This document provides an overview of HTTP architecture and its associated terminology, defines the "http" and "https" Uniform Resource Identifier (URI) schemes, defines the HTTP/1.1 message syntax and parsing requirements, and describes related security concerns for implementations.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Appendix B.1: ALPHA (letters), CR (carriage return), CRLF (CR LF), CTL (controls), DIGIT (decimal 0-9), DQUOTE (double quote), HEXDIG (hexadecimal 0-9/A-F/a-f), HTAB (horizontal tab), LF (line feed), OCTET (any 8-bit sequence of data), SP (space), and VCHAR (any visible [USASCII] character).
As a convention, ABNF rule names prefixed with "obs-" denote "obsolete" grammar rules that appear for historical reasons.
2. Architecture
HTTP was created for the World Wide Web (WWW) architecture and has evolved over time to support the scalability needs of a worldwide hypertext system. Much of that architecture is reflected in the terminology and syntax productions used to define HTTP.
2.1. Client/Server Messaging
HTTP is a stateless request/response protocol that operates by exchanging messages (Section 3) across a reliable transport- or session-layer "connection" (Section 6). An HTTP "client" is a program that establishes a connection to a server for the purpose of sending one or more HTTP requests. An HTTP "server" is a program that accepts connections in order to service HTTP requests by sending HTTP responses.
The terms "client" and "server" refer only to the roles that these programs perform for a particular connection. The same program might act as a client on some connections and a server on others. The term "user agent" refers to any of the various client programs that initiate a request, including (but not limited to) browsers, spiders (web-based robots), command-line tools, custom applications, and mobile apps. The term "origin server" refers to the program that can originate authoritative responses for a given target resource. The terms "sender" and "recipient" refer to any implementation that sends or receives a given message, respectively.
HTTP relies upon the Uniform Resource Identifier (URI) standard [RFC3986] to indicate the target resource (Section 5.1) and relationships between resources. Messages are passed in a format similar to that used by Internet mail [RFC5322] and the Multipurpose Internet Mail Extensions (MIME) [RFC2045] (see Appendix A of [RFC7231] for the differences between HTTP and MIME messages).
Most HTTP communication consists of a retrieval request (GET) for a representation of some resource identified by a URI. In the simplest case, this might be accomplished via a single bidirectional connection (===) between the user agent (UA) and the origin server (O).
request >
UA ======================================= O
< response
A client sends an HTTP request to a server in the form of a request message, beginning with a request-line that includes a method, URI, and protocol version (Section 3.1.1), followed by header fields containing request modifiers, client information, and representation metadata (Section 3.2), an empty line to indicate the end of the header section, and finally a message body containing the payload body (if any, Section 3.3).
A server responds to a client's request by sending one or more HTTP response messages, each beginning with a status line that includes the protocol version, a success or error code, and textual reason phrase (Section 3.1.2), possibly followed by header fields containing server information, resource metadata, and representation metadata (Section 3.2), an empty line to indicate the end of the header section, and finally a message body containing the payload body (if any, Section 3.3).
A connection might be used for multiple request/response exchanges, as defined in Section 6.3.
The following example illustrates a typical message exchange for a GET request (Section 4.3.1 of [RFC7231]) on the URI "http://www.example.com/hello.txt":
Client request:
GET /hello.txt HTTP/1.1 User-Agent: curl/7.16.3 libcurl/7.16.3 OpenSSL/0.9.7l zlib/1.2.3 Host: www.example.com Accept-Language: en, mi
Server response:
HTTP/1.1 200 OK
Date: Mon, 27 Jul 2009 12:28:53 GMT
Server: Apache
Last-Modified: Wed, 22 Jul 2009 19:15:56 GMT
ETag: "34aa387-d-1568eb00"
Accept-Ranges: bytes
Content-Length: 51
Vary: Accept-Encoding
Content-Type: text/plain
Hello World! My payload includes a trailing CRLF.
2.2. Implementation Diversity
When considering the design of HTTP, it is easy to fall into a trap of thinking that all user agents are general-purpose browsers and all origin servers are large public websites. That is not the case in practice. Common HTTP user agents include household appliances, stereos, scales, firmware update scripts, command-line programs, mobile apps, and communication devices in a multitude of shapes and sizes. Likewise, common HTTP origin servers include home automation units, configurable networking components, office machines, autonomous robots, news feeds, traffic cameras, ad selectors, and video-delivery platforms.
The term "user agent" does not imply that there is a human user directly interacting with the software agent at the time of a request. In many cases, a user agent is installed or configured to run in the background and save its results for later inspection (or save only a subset of those results that might be interesting or erroneous). Spiders, for example, are typically given a start URI and configured to follow certain behavior while crawling the Web as a hypertext graph.
The implementation diversity of HTTP means that not all user agents can make interactive suggestions to their user or provide adequate warning for security or privacy concerns. In the few cases where this specification requires reporting of errors to the user, it is acceptable for such reporting to only be observable in an error console or log file. Likewise, requirements that an automated action be confirmed by the user before proceeding might be met via advance configuration choices, run-time options, or simple avoidance of the unsafe action; confirmation does not imply any specific user interface or interruption of normal processing if the user has already made that choice.
2.3. Intermediaries
HTTP enables the use of intermediaries to satisfy requests through a chain of connections. There are three common forms of HTTP intermediary: proxy, gateway, and tunnel. In some cases, a single intermediary might act as an origin server, proxy, gateway, or tunnel, switching behavior based on the nature of each request.
> > > >
UA =========== A =========== B =========== C =========== O
< < < <
The figure above shows three intermediaries (A, B, and C) between the user agent and origin server. A request or response message that travels the whole chain will pass through four separate connections. Some HTTP communication options might apply only to the connection with the nearest, non-tunnel neighbor, only to the endpoints of the chain, or to all connections along the chain. Although the diagram is linear, each participant might be engaged in multiple, simultaneous communications. For example, B might be receiving requests from many clients other than A, and/or forwarding requests to servers other than C, at the same time that it is handling A's request. Likewise, later requests might be sent through a different path of connections, often based on dynamic configuration for load balancing.
The terms "upstream" and "downstream" are used to describe directional requirements in relation to the message flow: all messages flow from upstream to downstream. The terms "inbound" and "outbound" are used to describe directional requirements in relation to the request route: "inbound" means toward the origin server and "outbound" means toward the user agent.
A "proxy" is a message-forwarding agent that is selected by the client, usually via local configuration rules, to receive requests for some type(s) of absolute URI and attempt to satisfy those requests via translation through the HTTP interface. Some translations are minimal, such as for proxy requests for "http" URIs, whereas other requests might require translation to and from entirely different application-level protocols. Proxies are often used to group an organization's HTTP requests through a common intermediary for the sake of security, annotation services, or shared caching. Some proxies are designed to apply transformations to selected messages or payloads while they are being forwarded, as described in Section 5.7.2.
A "gateway" (a.k.a. "reverse proxy") is an intermediary that acts as an origin server for the outbound connection but translates received requests and forwards them inbound to another server or servers. Gateways are often used to encapsulate legacy or untrusted information services, to improve server performance through "accelerator" caching, and to enable partitioning or load balancing of HTTP services across multiple machines.
All HTTP requirements applicable to an origin server also apply to the outbound communication of a gateway. A gateway communicates with inbound servers using any protocol that it desires, including private extensions to HTTP that are outside the scope of this specification. However, an HTTP-to-HTTP gateway that wishes to interoperate with third-party HTTP servers ought to conform to user agent requirements on the gateway's inbound connection.
A "tunnel" acts as a blind relay between two connections without changing the messages. Once active, a tunnel is not considered a party to the HTTP communication, though the tunnel might have been initiated by an HTTP request. A tunnel ceases to exist when both ends of the relayed connection are closed. Tunnels are used to extend a virtual connection through an intermediary, such as when Transport Layer Security (TLS, [RFC5246]) is used to establish confidential communication through a shared firewall proxy.
The above categories for intermediary only consider those acting as participants in the HTTP communication. There are also intermediaries that can act on lower layers of the network protocol stack, filtering or redirecting HTTP traffic without the knowledge or permission of message senders. Network intermediaries are indistinguishable (at a protocol level) from a man-in-the-middle attack, often introducing security flaws or interoperability problems due to mistakenly violating HTTP semantics.
For example, an "interception proxy" [RFC3040] (also commonly known as a "transparent proxy" [RFC1919] or "captive portal") differs from an HTTP proxy because it is not selected by the client. Instead, an interception proxy filters or redirects outgoing TCP port 80 packets (and occasionally other common port traffic). Interception proxies are commonly found on public network access points, as a means of enforcing account subscription prior to allowing use of non-local Internet services, and within corporate firewalls to enforce network usage policies.
HTTP is defined as a stateless protocol, meaning that each request message can be understood in isolation. Many implementations depend on HTTP's stateless design in order to reuse proxied connections or dynamically load balance requests across multiple servers. Hence, a server MUST NOT assume that two requests on the same connection are from the same user agent unless the connection is secured and specific to that agent. Some non-standard HTTP extensions (e.g., [RFC4559]) have been known to violate this requirement, resulting in security and interoperability problems.
2.4. Caches
A "cache" is a local store of previous response messages and the subsystem that controls its message storage, retrieval, and deletion. A cache stores cacheable responses in order to reduce the response time and network bandwidth consumption on future, equivalent requests. Any client or server MAY employ a cache, though a cache cannot be used by a server while it is acting as a tunnel.
The effect of a cache is that the request/response chain is shortened if one of the participants along the chain has a cached response applicable to that request. The following illustrates the resulting chain if B has a cached copy of an earlier response from O (via C) for a request that has not been cached by UA or A.
> >
UA =========== A =========== B - - - - - - C - - - - - - O
< <
A response is "cacheable" if a cache is allowed to store a copy of the response message for use in answering subsequent requests. Even when a response is cacheable, there might be additional constraints placed by the client or by the origin server on when that cached response can be used for a particular request. HTTP requirements for cache behavior and cacheable responses are defined in Section 2 of [RFC7234].
There is a wide variety of architectures and configurations of caches deployed across the World Wide Web and inside large organizations. These include national hierarchies of proxy caches to save transoceanic bandwidth, collaborative systems that broadcast or multicast cache entries, archives of pre-fetched cache entries for use in off-line or high-latency environments, and so on.
2.5. Conformance and Error Handling
This specification targets conformance criteria according to the role of a participant in HTTP communication. Hence, HTTP requirements are placed on senders, recipients, clients, servers, user agents, intermediaries, origin servers, proxies, gateways, or caches, depending on what behavior is being constrained by the requirement. Additional (social) requirements are placed on implementations, resource owners, and protocol element registrations when they apply beyond the scope of a single communication.
The verb "generate" is used instead of "send" where a requirement differentiates between creating a protocol element and merely forwarding a received element downstream.
An implementation is considered conformant if it complies with all of the requirements associated with the roles it partakes in HTTP.
Conformance includes both the syntax and semantics of protocol elements. A sender MUST NOT generate protocol elements that convey a meaning that is known by that sender to be false. A sender MUST NOT generate protocol elements that do not match the grammar defined by the corresponding ABNF rules. Within a given message, a sender MUST NOT generate protocol elements or syntax alternatives that are only allowed to be generated by participants in other roles (i.e., a role that the sender does not have for that message).
When a received protocol element is parsed, the recipient MUST be able to parse any value of reasonable length that is applicable to the recipient's role and that matches the grammar defined by the corresponding ABNF rules. Note, however, that some received protocol elements might not be parsed. For example, an intermediary forwarding a message might parse a header-field into generic field-name and field-value components, but then forward the header field without further parsing inside the field-value.
HTTP does not have specific length limitations for many of its protocol elements because the lengths that might be appropriate will vary widely, depending on the deployment context and purpose of the implementation. Hence, interoperability between senders and recipients depends on shared expectations regarding what is a reasonable length for each protocol element. Furthermore, what is commonly understood to be a reasonable length for some protocol elements has changed over the course of the past two decades of HTTP use and is expected to continue changing in the future.
At a minimum, a recipient MUST be able to parse and process protocol element lengths that are at least as long as the values that it generates for those same protocol elements in other messages. For example, an origin server that publishes very long URI references to its own resources needs to be able to parse and process those same references when received as a request target.
A recipient MUST interpret a received protocol element according to the semantics defined for it by this specification, including extensions to this specification, unless the recipient has determined (through experience or configuration) that the sender incorrectly implements what is implied by those semantics. For example, an origin server might disregard the contents of a received Accept-Encoding header field if inspection of the User-Agent header field indicates a specific implementation version that is known to fail on receipt of certain content codings.
Unless noted otherwise, a recipient MAY attempt to recover a usable protocol element from an invalid construct. HTTP does not define specific error handling mechanisms except when they have a direct impact on security, since different applications of the protocol require different error handling strategies. For example, a Web browser might wish to transparently recover from a response where the Location header field doesn't parse according to the ABNF, whereas a systems control client might consider any form of error recovery to be dangerous.
2.6. Protocol Versioning
HTTP uses a "<major>.<minor>" numbering scheme to indicate versions of the protocol. This specification defines version "1.1". The protocol version as a whole indicates the sender's conformance with the set of requirements laid out in that version's corresponding specification of HTTP.
The version of an HTTP message is indicated by an HTTP-version field in the first line of the message. HTTP-version is case-sensitive.
HTTP-version = HTTP-name "/" DIGIT "." DIGIT HTTP-name = %x48.54.54.50 ; "HTTP", case-sensitive
The HTTP version number consists of two decimal digits separated by a "." (period or decimal point). The first digit ("major version") indicates the HTTP messaging syntax, whereas the second digit ("minor version") indicates the highest minor version within that major version to which the sender is conformant and able to understand for future communication. The minor version advertises the sender's communication capabilities even when the sender is only using a backwards-compatible subset of the protocol, thereby letting the recipient know that more advanced features can be used in response (by servers) or in future requests (by clients).
When an HTTP/1.1 message is sent to an HTTP/1.0 recipient [RFC1945] or a recipient whose version is unknown, the HTTP/1.1 message is constructed such that it can be interpreted as a valid HTTP/1.0 message if all of the newer features are ignored. This specification places recipient-version requirements on some new features so that a conformant sender will only use compatible features until it has determined, through configuration or the receipt of a message, that the recipient supports HTTP/1.1.
The interpretation of a header field does not change between minor versions of the same major HTTP version, though the default behavior of a recipient in the absence of such a field can change. Unless specified otherwise, header fields defined in HTTP/1.1 are defined for all versions of HTTP/1.x. In particular, the Host and Connection header fields ought to be implemented by all HTTP/1.x implementations whether or not they advertise conformance with HTTP/1.1.
New header fields can be introduced without changing the protocol version if their defined semantics allow them to be safely ignored by recipients that do not recognize them. Header field extensibility is discussed in Section 3.2.1.
Intermediaries that process HTTP messages (i.e., all intermediaries other than those acting as tunnels) MUST send their own HTTP-version in forwarded messages. In other words, they are not allowed to blindly forward the first line of an HTTP message without ensuring that the protocol version in that message matches a version to which that intermediary is conformant for both the receiving and sending of messages. Forwarding an HTTP message without rewriting the HTTP-version might result in communication errors when downstream recipients use the message sender's version to determine what features are safe to use for later communication with that sender.
A client SHOULD send a request version equal to the highest version to which the client is conformant and whose major version is no higher than the highest version supported by the server, if this is known. A client MUST NOT send a version to which it is not conformant.
A client MAY send a lower request version if it is known that the server incorrectly implements the HTTP specification, but only after the client has attempted at least one normal request and determined from the response status code or header fields (e.g., Server) that the server improperly handles higher request versions.
A server SHOULD send a response version equal to the highest version to which the server is conformant that has a major version less than or equal to the one received in the request. A server MUST NOT send a version to which it is not conformant. A server can send a 505 (HTTP Version Not Supported) response if it wishes, for any reason, to refuse service of the client's major protocol version.
A server MAY send an HTTP/1.0 response to a request if it is known or suspected that the client incorrectly implements the HTTP specification and is incapable of correctly processing later version responses, such as when a client fails to parse the version number correctly or when an intermediary is known to blindly forward the HTTP-version even when it doesn't conform to the given minor version of the protocol. Such protocol downgrades SHOULD NOT be performed unless triggered by specific client attributes, such as when one or more of the request header fields (e.g., User-Agent) uniquely match the values sent by a client known to be in error.
The intention of HTTP's versioning design is that the major number will only be incremented if an incompatible message syntax is introduced, and that the minor number will only be incremented when changes made to the protocol have the effect of adding to the message semantics or implying additional capabilities of the sender. However, the minor version was not incremented for the changes introduced between [RFC2068] and [RFC2616], and this revision has specifically avoided any such changes to the protocol.
When an HTTP message is received with a major version number that the recipient implements, but a higher minor version number than what the recipient implements, the recipient SHOULD process the message as if it were in the highest minor version within that major version to which the recipient is conformant. A recipient can assume that a message with a higher minor version, when sent to a recipient that has not yet indicated support for that higher version, is sufficiently backwards-compatible to be safely processed by any implementation of the same major version.
2.7. Uniform Resource Identifiers
Uniform Resource Identifiers (URIs) [RFC3986] are used throughout HTTP as the means for identifying resources (Section 2 of [RFC7231]). URI references are used to target requests, indicate redirects, and define relationships.
The definitions of "URI-reference", "absolute-URI", "relative-part", "scheme", "authority", "port", "host", "path-abempty", "segment", "query", and "fragment" are adopted from the URI generic syntax. An "absolute-path" rule is defined for protocol elements that can contain a non-empty path component. (This rule differs slightly from the path-abempty rule of RFC 3986, which allows for an empty path to be used in references, and path-absolute rule, which does not allow paths that begin with "/".) A "partial-URI" rule is defined for protocol elements that can contain a relative URI but not a fragment component.
URI-reference = <URI-reference, see [RFC3986], Section 4.1> absolute-URI = <absolute-URI, see [RFC3986], Section 4.3> relative-part = <relative-part, see [RFC3986], Section 4.2> scheme = <scheme, see [RFC3986], Section 3.1> authority = <authority, see [RFC3986], Section 3.2> uri-host = <host, see [RFC3986], Section 3.2.2> port = <port, see [RFC3986], Section 3.2.3> path-abempty = <path-abempty, see [RFC3986], Section 3.3> segment = <segment, see [RFC3986], Section 3.3> query = <query, see [RFC3986], Section 3.4> fragment = <fragment, see [RFC3986], Section 3.5> absolute-path = 1*( "/" segment ) partial-URI = relative-part [ "?" query ]
Each protocol element in HTTP that allows a URI reference will indicate in its ABNF production whether the element allows any form of reference (URI-reference), only a URI in absolute form (absolute-URI), only the path and optional query components, or some combination of the above. Unless otherwise indicated, URI references are parsed relative to the effective request URI (Section 5.5).
2.7.1. http URI Scheme
The "http" URI scheme is hereby defined for the purpose of minting identifiers according to their association with the hierarchical namespace governed by a potential HTTP origin server listening for TCP ([RFC0793]) connections on a given port.
http-URI = "http:" "/" authority path-abempty [ "?" query ] [ "#" fragment ]
The origin server for an "http" URI is identified by the authority component, which includes a host identifier and optional TCP port ([RFC3986], Section 3.2.1) for including user authentication information in the URI. Some implementations make use of the userinfo component for internal configuration of authentication information, such as within command invocation options, configuration files, or bookmark lists, even though such usage might expose a user identifier or password. A sender MUST NOT generate the userinfo subcomponent (and its "@" delimiter) when an "http" URI reference is generated within a message as a request target or header field value. Before making use of an "http" URI reference received from an untrusted source, a recipient SHOULD parse for userinfo and treat its presence as an error; it is likely being used to obscure the authority for the sake of phishing attacks.
2.7.2. https URI Scheme
The "https" URI scheme is hereby defined for the purpose of minting identifiers according to their association with the hierarchical namespace governed by a potential HTTP origin server listening to a given TCP port for TLS-secured connections ([RFC5246]).
All of the requirements listed above for the "http" scheme are also requirements for the "https" scheme, except that TCP port 443 is the default if the port subcomponent is empty or not given, and the user agent MUST ensure that its connection to the origin server is secured through the use of strong encryption, end-to-end, prior to sending the first HTTP request.
https-URI = "https:" "/" authority path-abempty [ "?" query ] [ "#" fragment ]
Note that the "https" URI scheme depends on both TLS and TCP for establishing authority. Resources made available via the "https" scheme have no shared identity with the "http" scheme even if their resource identifiers indicate the same authority (the same host listening to the same TCP port). They are distinct namespaces and are considered to be distinct origin servers. However, an extension to HTTP that is defined to apply to entire host domains, such as the Cookie protocol [RFC6265], can allow information set by one service to impact communication with other services within a matching group of host domains.
The process for authoritative access to an "https" identified resource is defined in [RFC2818].
2.7.3. http and https URI Normalization and Comparison
Since the "http" and "https" schemes conform to the URI generic syntax, such URIs are normalized and compared according to the algorithm defined in 2.2 of [RFC3986]).
For example, the following three URIs are equivalent:
http://example.com:80/~smith/home.html http://EXAMPLE.com/%7Esmith/home.html http://EXAMPLE.com:/%7esmith/home.html
3. Message Format
All HTTP/1.1 messages consist of a start-line followed by a sequence of octets in a format similar to the Internet Message Format [RFC5322]: zero or more header fields (collectively referred to as the "headers" or the "header section"), an empty line indicating the end of the header section, and an optional message body.
HTTP-message = start-line *( header-field CRLF ) CRLF [ message-body ]
The normal procedure for parsing an HTTP message is to read the start-line into a structure, read each header field into a hash table by field name until the empty line, and then use the parsed data to determine if a message body is expected. If a message body has been indicated, then it is read as a stream until an amount of octets equal to the message body length is read or the connection is closed.
A recipient MUST parse an HTTP message as a sequence of octets in an encoding that is a superset of US-ASCII [USASCII]. Parsing an HTTP message as a stream of Unicode characters, without regard for the specific encoding, creates security vulnerabilities due to the varying ways that string processing libraries handle invalid multibyte character sequences that contain the octet LF (%x0A). String-based parsers can only be safely used within protocol elements after the element has been extracted from the message, such as within a header field-value after message parsing has delineated the individual fields.
An HTTP message can be parsed as a stream for incremental processing or forwarding downstream. However, recipients cannot rely on incremental delivery of partial messages, since some implementations will buffer or delay message forwarding for the sake of network efficiency, security checks, or payload transformations.
A sender MUST NOT send whitespace between the start-line and the first header field. A recipient that receives whitespace between the start-line and the first header field MUST either reject the message as invalid or consume each whitespace-preceded line without further processing of it (i.e., ignore the entire line, along with any subsequent lines preceded by whitespace, until a properly formed header field is received or the header section is terminated).
The presence of such whitespace in a request might be an attempt to trick a server into ignoring that field or processing the line after it as a new request, either of which might result in a security vulnerability if other implementations within the request chain interpret the same message differently. Likewise, the presence of such whitespace in a response might be ignored by some clients or cause others to cease parsing.
3.1. Start Line
An HTTP message can be either a request from client to server or a response from server to client. Syntactically, the two types of message differ only in the start-line, which is either a request-line (for requests) or a status-line (for responses), and in the algorithm for determining the length of the message body (Section 3.3).
In theory, a client could receive requests and a server could receive responses, distinguishing them by their different start-line formats, but, in practice, servers are implemented to only expect a request (a response is interpreted as an unknown or invalid request method) and clients are implemented to only expect a response.
3.1.1. Request Line
A request-line begins with a method token, followed by a single space (SP), the request-target, another single space (SP), the protocol version, and ends with CRLF.
The method token indicates the request method to be performed on the target resource. The request method is case-sensitive.
The request methods defined by this specification can be found in Section 4 of [RFC7231], along with information regarding the HTTP method registry and considerations for defining new methods.
The request-target identifies the target resource upon which to apply the request, as defined in Section 5.3.
Recipients typically parse the request-line into its component parts by splitting on whitespace (see Section 3.5), since no whitespace is allowed in the three components. Unfortunately, some user agents fail to properly encode or exclude whitespace found in hypertext references, resulting in those disallowed characters being sent in a request-target.
Recipients of an invalid request-line SHOULD respond with either a 400 (Bad Request) error or a 301 (Moved Permanently) redirect with the request-target properly encoded. A recipient SHOULD NOT attempt to autocorrect and then process the request without a redirect, since the invalid request-line might be deliberately crafted to bypass security filters along the request chain.
HTTP does not place a predefined limit on the length of a request-line, as described in Section 2.5. A server that receives a method longer than any that it implements SHOULD respond with a 501 (Not Implemented) status code. A server that receives a request-target longer than any URI it wishes to parse MUST respond with a 414 (URI Too Long) status code (see Section 6.5.12 of [RFC7231]).
Various ad hoc limitations on request-line length are found in practice. It is RECOMMENDED that all HTTP senders and recipients support, at a minimum, request-line lengths of 8000 octets.
3.1.2. Status Line
The first line of a response message is the status-line, consisting of the protocol version, a space (SP), the status code, another space, a possibly empty textual phrase describing the status code, and ending with CRLF.
The status-code element is a 3-digit integer code describing the result of the server's attempt to understand and satisfy the client's corresponding request. The rest of the response message is to be interpreted in light of the semantics defined for that status code. See Section 6 of [RFC7231] for information about the semantics of status codes, including the classes of status code (indicated by the first digit), the status codes defined by this specification, considerations for the definition of new status codes, and the IANA registry.
status-code = 3DIGIT
The reason-phrase element exists for the sole purpose of providing a textual description associated with the numeric status code, mostly out of deference to earlier Internet application protocols that were more frequently used with interactive text clients. A client SHOULD ignore the reason-phrase content.
reason-phrase = *( HTAB / SP / VCHAR / obs-text )
3.2. Header Fields
Each header field consists of a case-insensitive field name followed by a colon (":"), optional leading whitespace, the field value, and optional trailing whitespace.
header-field = field-name ":" OWS field-value OWS field-name = token field-value = *( field-content / obs-fold ) field-content = field-vchar [ 1*( SP / HTAB ) field-vchar ] field-vchar = VCHAR / obs-text obs-fold = CRLF 1*( SP / HTAB ) ; obsolete line folding ; see Section 3.2.4
The field-name token labels the corresponding field-value as having the semantics defined by that header field. For example, the Date header field is defined in Section 7.1.1.2 of [RFC7231] as containing the origination timestamp for the message in which it appears.
3.2.1. Field Extensibility
Header fields are fully extensible: there is no limit on the introduction of new field names, each presumably defining new semantics, nor on the number of header fields used in a given message. Existing fields are defined in each part of this specification and in many other specifications outside this document set.
New header fields can be defined such that, when they are understood by a recipient, they might override or enhance the interpretation of previously defined header fields, define preconditions on request evaluation, or refine the meaning of responses.
A proxy MUST forward unrecognized header fields unless the field-name is listed in the Connection header field (Section 6.1) or the proxy is specifically configured to block, or otherwise transform, such fields. Other recipients SHOULD ignore unrecognized header fields. These requirements allow HTTP's functionality to be enhanced without requiring prior update of deployed intermediaries.
All defined header fields ought to be registered with IANA in the "Message Headers" registry, as described in Section 8.3 of [RFC7231].
3.2.2. Field Order
The order in which header fields with differing field names are received is not significant. However, it is good practice to send header fields that contain control data first, such as Host on requests and Date on responses, so that implementations can decide when not to handle a message as early as possible. A server MUST NOT apply a request to the target resource until the entire request header section is received, since later header fields might include conditionals, authentication credentials, or deliberately misleading duplicate header fields that would impact request processing.
A sender MUST NOT generate multiple header fields with the same field name in a message unless either the entire field value for that header field is defined as a comma-separated list [i.e., #(values)] or the header field is a well-known exception (as noted below).
A recipient MAY combine multiple header fields with the same field name into one "field-name: field-value" pair, without changing the semantics of the message, by appending each subsequent field value to the combined field value in order, separated by a comma. The order in which header fields with the same field name are received is therefore significant to the interpretation of the combined field value; a proxy MUST NOT change the order of these field values when forwarding a message.
3.2.3. Whitespace
This specification uses three rules to denote the use of linear whitespace: OWS (optional whitespace), RWS (required whitespace), and BWS ("bad" whitespace).
The OWS rule is used where zero or more linear whitespace octets might appear. For protocol elements where optional whitespace is preferred to improve readability, a sender SHOULD generate the optional whitespace as a single SP; otherwise, a sender SHOULD NOT generate optional whitespace except as needed to white out invalid or unwanted protocol elements during in-place message filtering.
The RWS rule is used when at least one linear whitespace octet is required to separate field tokens. A sender SHOULD generate RWS as a single SP.
The BWS rule is used where the grammar allows optional whitespace only for historical reasons. A sender MUST NOT generate BWS in messages. A recipient MUST parse for such bad whitespace and remove it before interpreting the protocol element.
OWS = *( SP / HTAB ) ; optional whitespace RWS = 1*( SP / HTAB ) ; required whitespace BWS = OWS ; "bad" whitespace
3.2.4. Field Parsing
Messages are parsed using a generic algorithm, independent of the individual header field names. The contents within a given field value are not parsed until a later stage of message interpretation (usually after the message's entire header section has been processed). Consequently, this specification does not use ABNF rules to define each "Field-Name: Field Value" pair, as was done in previous editions. Instead, this specification uses ABNF rules that are named according to each registered field name, wherein the rule defines the valid grammar for that field's corresponding field values (i.e., after the field-value has been extracted from the header section by a generic field parser).
No whitespace is allowed between the header field-name and colon. In the past, differences in the handling of such whitespace have led to security vulnerabilities in request routing and response handling. A server MUST reject any received request message that contains whitespace between a header field-name and colon with a response code of 400 (Bad Request). A proxy MUST remove any such whitespace from a response message before forwarding the message downstream.
A field value might be preceded and/or followed by optional whitespace (OWS); a single SP preceding the field-value is preferred for consistent readability by humans. The field value does not include any leading or trailing whitespace: OWS occurring before the first non-whitespace octet of the field value or after the last non-whitespace octet of the field value ought to be excluded by parsers when extracting the field value from a header field.
Historically, HTTP header field values could be extended over multiple lines by preceding each extra line with at least one space or horizontal tab (obs-fold). This specification deprecates such line folding except within the message/http media type (Section 8.3.1). A sender MUST NOT generate a message that includes line folding (i.e., that has any field-value that contains a match to the obs-fold rule) unless the message is intended for packaging within the message/http media type.
A server that receives an obs-fold in a request message that is not within a message/http container MUST either reject the message by sending a 400 (Bad Request), preferably with a representation explaining that obsolete line folding is unacceptable, or replace each received obs-fold with one or more SP octets prior to interpreting the field value or forwarding the message downstream.
A proxy or gateway that receives an obs-fold in a response message that is not within a message/http container MUST either discard the message and replace it with a 502 (Bad Gateway) response, preferably with a representation explaining that unacceptable line folding was received, or replace each received obs-fold with one or more SP octets prior to interpreting the field value or forwarding the message downstream.
A user agent that receives an obs-fold in a response message that is not within a message/http container MUST replace each received obs-fold with one or more SP octets prior to interpreting the field value.
Historically, HTTP has allowed field content with text in the ISO-8859-1 charset [ISO-8859-1], supporting other charsets only through use of [RFC2047] encoding. In practice, most HTTP header field values use only a subset of the US-ASCII charset [USASCII]. Newly defined header fields SHOULD limit their field values to US-ASCII octets. A recipient SHOULD treat other octets in field content (obs-text) as opaque data.
3.2.5. Field Limits
HTTP does not place a predefined limit on the length of each header field or on the length of the header section as a whole, as described in Section 2.5. Various ad hoc limitations on individual header field length are found in practice, often depending on the specific field semantics.
A server that receives a request header field, or set of fields, larger than it wishes to process MUST respond with an appropriate 4xx (Client Error) status code. Ignoring such header fields would increase the server's vulnerability to request smuggling attacks (Section 9.5).
A client MAY discard or truncate received header fields that are larger than the client wishes to process if the field semantics are such that the dropped value(s) can be safely ignored without changing the message framing or response semantics.
3.2.6. Field Value Components
Most HTTP header field values are defined using common syntax components (token, quoted-string, and comment) separated by whitespace or specific delimiting characters. Delimiters are chosen from the set of US-ASCII visual characters not allowed in a token (DQUOTE and "(),/:;<=>?@[\]{}").
A string of text is parsed as a single value if it is quoted using double-quote marks.
quoted-string = DQUOTE *( qdtext / quoted-pair ) DQUOTE qdtext = HTAB / SP /%x21 / %x23-5B / %x5D-7E / obs-text obs-text = %x80-FF
Comments can be included in some HTTP header fields by surrounding the comment text with parentheses. Comments are only allowed in fields containing "comment" as part of their field value definition.
The backslash octet ("\") can be used as a single-octet quoting mechanism within quoted-string and comment constructs. Recipients that process the value of a quoted-string MUST handle a quoted-pair as if it were replaced by the octet following the backslash.
quoted-pair = "\" ( HTAB / SP / VCHAR / obs-text )
A sender SHOULD NOT generate a quoted-pair in a quoted-string except where necessary to quote DQUOTE and backslash octets occurring within that string. A sender SHOULD NOT generate a quoted-pair in a comment except where necessary to quote parentheses ["(" and ")"] and backslash octets occurring within that comment.
3.3. Message Body
The message body (if any) of an HTTP message is used to carry the payload body of that request or response. The message body is identical to the payload body unless a transfer coding has been applied, as described in Section 3.3.1.
message-body = *OCTET
The rules for when a message body is allowed in a message differ for requests and responses.
The presence of a message body in a request is signaled by a Content-Length or Transfer-Encoding header field. Request message framing is independent of method semantics, even if the method does not define any use for a message body.
The presence of a message body in a response depends on both the request method to which it is responding and the response status code (Section 3.1.2). Responses to the HEAD request method (Section 4.3.2 of [RFC7231]) never include a message body because the associated response header fields (e.g., Transfer-Encoding, Content-Length, etc.), if present, indicate only what their values would have been if the request method had been GET (Section 4.3.1 of [RFC7231]). 2xx (Successful) responses to a CONNECT request method (Section 4.3.6 of [RFC7231]) switch to tunnel mode instead of having a message body. All 1xx (Informational), 204 (No Content), and 304 (Not Modified) responses do not include a message body. All other responses do include a message body, although the body might be of zero length.
3.3.1. Transfer-Encoding
The Transfer-Encoding header field lists the transfer coding names corresponding to the sequence of transfer codings that have been (or will be) applied to the payload body in order to form the message body. Transfer codings are defined in Section 4.
Transfer-Encoding is analogous to the Content-Transfer-Encoding field of MIME, which was designed to enable safe transport of binary data over a 7-bit transport service ([RFC2045], Section 6). However, safe transport has a different focus for an 8bit-clean transfer protocol. In HTTP's case, Transfer-Encoding is primarily intended to accurately delimit a dynamically generated payload and to distinguish payload encodings that are only applied for transport efficiency or security from those that are characteristics of the selected resource.
A recipient MUST be able to parse the chunked transfer coding (Section 4.1) because it plays a crucial role in framing messages when the payload body size is not known in advance. A sender MUST NOT apply chunked more than once to a message body (i.e., chunking an already chunked message is not allowed). If any transfer coding other than chunked is applied to a request payload body, the sender MUST apply chunked as the final transfer coding to ensure that the message is properly framed. If any transfer coding other than chunked is applied to a response payload body, the sender MUST either apply chunked as the final transfer coding or terminate the message by closing the connection.
For example,
Transfer-Encoding: gzip, chunked
indicates that the payload body has been compressed using the gzip coding and then chunked using the chunked coding while forming the message body.
Unlike Content-Encoding (Section 3.1.2.1 of [RFC7231]), Transfer-Encoding is a property of the message, not of the representation, and any recipient along the request/response chain MAY decode the received transfer coding(s) or apply additional transfer coding(s) to the message body, assuming that corresponding changes are made to the Transfer-Encoding field-value. Additional information about the encoding parameters can be provided by other header fields not defined by this specification.
Transfer-Encoding MAY be sent in a response to a HEAD request or in a 304 (Not Modified) response (Section 4.1 of [RFC7232]) to a GET request, neither of which includes a message body, to indicate that the origin server would have applied a transfer coding to the message body if the request had been an unconditional GET. This indication is not required, however, because any recipient on the response chain (including the origin server) can remove transfer codings when they are not needed.
A server MUST NOT send a Transfer-Encoding header field in any response with a status code of 1xx (Informational) or 204 (No Content). A server MUST NOT send a Transfer-Encoding header field in any 2xx (Successful) response to a CONNECT request (Section 4.3.6 of [RFC7231]).
Transfer-Encoding was added in HTTP/1.1. It is generally assumed that implementations advertising only HTTP/1.0 support will not understand how to process a transfer-encoded payload. A client MUST NOT send a request containing Transfer-Encoding unless it knows the server will handle HTTP/1.1 (or later) requests; such knowledge might be in the form of specific user configuration or by remembering the version of a prior received response. A server MUST NOT send a response containing Transfer-Encoding unless the corresponding request indicates HTTP/1.1 (or later).
A server that receives a request message with a transfer coding it does not understand SHOULD respond with 501 (Not Implemented).
3.3.2. Content-Length
When a message does not have a Transfer-Encoding header field, a Content-Length header field can provide the anticipated size, as a decimal number of octets, for a potential payload body. For messages that do include a payload body, the Content-Length field-value provides the framing information necessary for determining where the body (and message) ends. For messages that do not include a payload body, the Content-Length indicates the size of the selected representation (Section 3 of [RFC7231]).
Content-Length = 1*DIGIT
An example is
Content-Length: 3495
A sender MUST NOT send a Content-Length header field in any message that contains a Transfer-Encoding header field.
A user agent SHOULD send a Content-Length in a request message when no Transfer-Encoding is sent and the request method defines a meaning for an enclosed payload body. For example, a Content-Length header field is normally sent in a POST request even when the value is 0 (indicating an empty payload body). A user agent SHOULD NOT send a Content-Length header field when the request message does not contain a payload body and the method semantics do not anticipate such a body.
A server MAY send a Content-Length header field in a response to a HEAD request (Section 4.3.2 of [RFC7231]); a server MUST NOT send Content-Length in such a response unless its field-value equals the decimal number of octets that would have been sent in the payload body of a response if the same request had used the GET method.
A server MAY send a Content-Length header field in a 304 (Not Modified) response to a conditional GET request (Section 4.1 of [RFC7232]); a server MUST NOT send Content-Length in such a response unless its field-value equals the decimal number of octets that would have been sent in the payload body of a 200 (OK) response to the same request.
A server MUST NOT send a Content-Length header field in any response with a status code of 1xx (Informational) or 204 (No Content). A server MUST NOT send a Content-Length header field in any 2xx (Successful) response to a CONNECT request (Section 4.3.6 of [RFC7231]).
Aside from the cases defined above, in the absence of Transfer-Encoding, an origin server SHOULD send a Content-Length header field when the payload body size is known prior to sending the complete header section. This will allow downstream recipients to measure transfer progress, know when a received message is complete, and potentially reuse the connection for additional requests.
Any Content-Length field value greater than or equal to zero is valid. Since there is no predefined limit to the length of a payload, a recipient MUST anticipate potentially large decimal numerals and prevent parsing errors due to integer conversion overflows (Section 9.3).
If a message is received that has multiple Content-Length header fields with field-values consisting of the same decimal value, or a single Content-Length header field with a field value containing a list of identical decimal values (e.g., "Content-Length: 42, 42"), indicating that duplicate Content-Length header fields have been generated or combined by an upstream message processor, then the recipient MUST either reject the message as invalid or replace the duplicated field-values with a single valid Content-Length field containing that decimal value prior to determining the message body length or forwarding the message.
3.3.3. Message Body Length
The length of a message body is determined by one of the following (in order of precedence):
Any response to a HEAD request and any response with a 1xx (Informational), 204 (No Content), or 304 (Not Modified) status code is always terminated by the first empty line after the header fields, regardless of the header fields present in the message, and thus cannot contain a message body.
Any 2xx (Successful) response to a CONNECT request implies that the connection will become a tunnel immediately after the empty line that concludes the header fields. A client MUST ignore any Content-Length or Transfer-Encoding header fields received in such a message.
If a Transfer-Encoding header field is present and the chunked transfer coding (Section 4.1) is the final encoding, the message body length is determined by reading and decoding the chunked data until the transfer coding indicates the data is complete.
If a Transfer-Encoding header field is present in a response and the chunked transfer coding is not the final encoding, the message body length is determined by reading the connection until it is closed by the server. If a Transfer-Encoding header field is present in a request and the chunked transfer coding is not the final encoding, the message body length cannot be determined reliably; the server MUST respond with the 400 (Bad Request) status code and then close the connection.
If a message is received with both a Transfer-Encoding and a Content-Length header field, the Transfer-Encoding overrides the Content-Length. Such a message might indicate an attempt to perform request smuggling (Section 9.5) or response splitting (Section 9.4) and ought to be handled as an error. A sender MUST remove the received Content-Length field prior to forwarding such a message downstream.
If a message is received without Transfer-Encoding and with either multiple Content-Length header fields having differing field-values or a single Content-Length header field having an invalid value, then the message framing is invalid and the recipient MUST treat it as an unrecoverable error. If this is a request message, the server MUST respond with a 400 (Bad Request) status code and then close the connection. If this is a response message received by a proxy, the proxy MUST close the connection to the server, discard the received response, and send a 502 (Bad Gateway) response to the client. If this is a response message received by a user agent, the user agent MUST close the connection to the server and discard the received response.
If a valid Content-Length header field is present without Transfer-Encoding, its decimal value defines the expected message body length in octets. If the sender closes the connection or the recipient times out before the indicated number of octets are received, the recipient MUST consider the message to be incomplete and close the connection.
If this is a request message and none of the above are true, then the message body length is zero (no message body is present).
Otherwise, this is a response message without a declared message body length, so the message body length is determined by the number of octets received prior to the server closing the connection.
Since there is no way to distinguish a successfully completed, close-delimited message from a partially received message interrupted by network failure, a server SHOULD generate encoding or length-delimited messages whenever possible. The close-delimiting feature exists primarily for backwards compatibility with HTTP/1.0.
A server MAY reject a request that contains a message body but not a Content-Length by responding with 411 (Length Required).
Unless a transfer coding other than chunked has been applied, a client that sends a request containing a message body SHOULD use a valid Content-Length header field if the message body length is known in advance, rather than the chunked transfer coding, since some existing services respond to chunked with a 411 (Length Required) status code even though they understand the chunked transfer coding. This is typically because such services are implemented via a gateway that requires a content-length in advance of being called and the server is unable or unwilling to buffer the entire request before processing.
A user agent that sends a request containing a message body MUST send a valid Content-Length header field if it does not know the server will handle HTTP/1.1 (or later) requests; such knowledge can be in the form of specific user configuration or by remembering the version of a prior received response.
If the final response to the last request on a connection has been completely received and there remains additional data to read, a user agent MAY discard the remaining data or attempt to determine if that data belongs as part of the prior response body, which might be the case if the prior message's Content-Length value is incorrect. A client MUST NOT process, cache, or forward such extra data as a separate response, since such behavior would be vulnerable to cache poisoning.
3.4. Handling Incomplete Messages
A server that receives an incomplete request message, usually due to a canceled request or a triggered timeout exception, MAY send an error response prior to closing the connection.
A client that receives an incomplete response message, which can occur when a connection is closed prematurely or when decoding a supposedly chunked transfer coding fails, MUST record the message as incomplete. Cache requirements for incomplete responses are defined in Section 3 of [RFC7234].
If a response terminates in the middle of the header section (before the empty line is received) and the status code might rely on header fields to convey the full meaning of the response, then the client cannot assume that meaning has been conveyed; the client might need to repeat the request in order to determine what action to take next.
A message body that uses the chunked transfer coding is incomplete if the zero-sized chunk that terminates the encoding has not been received. A message that uses a valid Content-Length is incomplete if the size of the message body received (in octets) is less than the value given by Content-Length. A response that has neither chunked transfer coding nor Content-Length is terminated by closure of the connection and, thus, is considered complete regardless of the number of message body octets received, provided that the header section was received intact.
3.5. Message Parsing Robustness
Older HTTP/1.0 user agent implementations might send an extra CRLF after a POST request as a workaround for some early server applications that failed to read message body content that was not terminated by a line-ending. An HTTP/1.1 user agent MUST NOT preface or follow a request with an extra CRLF. If terminating the request message body with a line-ending is desired, then the user agent MUST count the terminating CRLF octets as part of the message body length.
In the interest of robustness, a server that is expecting to receive and parse a request-line SHOULD ignore at least one empty line (CRLF) received prior to the request-line.
Although the line terminator for the start-line and header fields is the sequence CRLF, a recipient MAY recognize a single LF as a line terminator and ignore any preceding CR.
Although the request-line and status-line grammar rules require that each of the component elements be separated by a single SP octet, recipients MAY instead parse on whitespace-delimited word boundaries and, aside from the CRLF terminator, treat any form of whitespace as the SP separator while ignoring preceding or trailing whitespace; such whitespace includes one or more of the following octets: SP, HTAB, VT (%x0B), FF (%x0C), or bare CR. However, lenient parsing can result in security vulnerabilities if there are multiple recipients of the message and each has its own unique interpretation of robustness (see Section 9.5).
When a server listening only for HTTP request messages, or processing what appears from the start-line to be an HTTP request message, receives a sequence of octets that does not match the HTTP-message grammar aside from the robustness exceptions listed above, the server SHOULD respond with a 400 (Bad Request) response.
4. Transfer Codings
Transfer coding names are used to indicate an encoding transformation that has been, can be, or might need to be applied to a payload body in order to ensure "safe transport" through the network. This differs from a content coding in that the transfer coding is a property of the message rather than a property of the representation that is being transferred.
transfer-coding = "chunked" ; Section 4.1 / "compress" ; Section 4.2.1 / "deflate" ; Section 4.2.2 / "gzip" ; Section 4.2.3 / transfer-extension transfer-extension = token *( OWS ";" OWS transfer-parameter )
Parameters are in the form of a name or name=value pair.
transfer-parameter = token BWS "=" BWS ( token / quoted-string )
All transfer-coding names are case-insensitive and ought to be registered within the HTTP Transfer Coding registry, as defined in Section 8.4. They are used in the TE (Section 4.3) and Transfer-Encoding (Section 3.3.1) header fields.
4.1. Chunked Transfer Coding
The chunked transfer coding wraps the payload body in order to transfer it as a series of chunks, each with its own size indicator, followed by an OPTIONAL trailer containing header fields. Chunked enables content streams of unknown size to be transferred as a sequence of length-delimited buffers, which enables the sender to retain connection persistence and the recipient to know when it has received the entire message.
chunked-body = *chunk last-chunk trailer-part CRLF chunk = chunk-size [ chunk-ext ] CRLF chunk-data CRLF chunk-size = 1*HEXDIG last-chunk = 1*("0") [ chunk-ext ] CRLF chunk-data = 1*OCTET ; a sequence of chunk-size octets
The chunk-size field is a string of hex digits indicating the size of the chunk-data in octets. The chunked transfer coding is complete when a chunk with a chunk-size of zero is received, possibly followed by a trailer, and finally terminated by an empty line.
A recipient MUST be able to parse and decode the chunked transfer coding.
4.1.1. Chunk Extensions
The chunked encoding allows each chunk to include zero or more chunk extensions, immediately following the chunk-size, for the sake of supplying per-chunk metadata (such as a signature or hash), mid-message control information, or randomization of message body size.
chunk-ext = *( ";" chunk-ext-name [ "=" chunk-ext-val ] ) chunk-ext-name = token chunk-ext-val = token / quoted-string
The chunked encoding is specific to each connection and is likely to be removed or recoded by each recipient (including intermediaries) before any higher-level application would have a chance to inspect the extensions. Hence, use of chunk extensions is generally limited to specialized HTTP services such as "long polling" (where client and server can have shared expectations regarding the use of chunk extensions) or for padding within an end-to-end secured connection.
A recipient MUST ignore unrecognized chunk extensions. A server ought to limit the total length of chunk extensions received in a request to an amount reasonable for the services provided, in the same way that it applies length limitations and timeouts for other parts of a message, and generate an appropriate 4xx (Client Error) response if that amount is exceeded.
4.1.2. Chunked Trailer Part
A trailer allows the sender to include additional fields at the end of a chunked message in order to supply metadata that might be dynamically generated while the message body is sent, such as a message integrity check, digital signature, or post-processing status. The trailer fields are identical to header fields, except they are sent in a chunked trailer instead of the message's header section.
trailer-part = *( header-field CRLF )
A sender MUST NOT generate a trailer that contains a field necessary for message framing (e.g., Transfer-Encoding and Content-Length), routing (e.g., Host), request modifiers (e.g., controls and conditionals in Section 5 of [RFC7231]), authentication (e.g., see [RFC7235] and [RFC6265]), response control data (e.g., see Section 7.1 of [RFC7231]), or determining how to process the payload (e.g., Content-Encoding, Content-Type, Content-Range, and Trailer).
When a chunked message containing a non-empty trailer is received, the recipient MAY process the fields (aside from those forbidden above) as if they were appended to the message's header section. A recipient MUST ignore (or consider as an error) any fields that are forbidden to be sent in a trailer, since processing them as if they were present in the header section might bypass external security filters.
Unless the request includes a TE header field indicating "trailers" is acceptable, as described in Section 4.3, a server SHOULD NOT generate trailer fields that it believes are necessary for the user agent to receive. Without a TE containing "trailers", the server ought to assume that the trailer fields might be silently discarded along the path to the user agent. This requirement allows intermediaries to forward a de-chunked message to an HTTP/1.0 recipient without buffering the entire response.
4.1.3. Decoding Chunked
A process for decoding the chunked transfer coding can be represented in pseudo-code as:
length := 0
read chunk-size, chunk-ext (if any), and CRLF
while (chunk-size > 0) {
read chunk-data and CRLF
append chunk-data to decoded-body
length := length + chunk-size
read chunk-size, chunk-ext (if any), and CRLF
}
read trailer field
while (trailer field is not empty) {
if (trailer field is allowed to be sent in a trailer) {
append trailer field to existing header fields
}
read trailer-field
}
Content-Length := length
Remove "chunked" from Transfer-Encoding
Remove Trailer from existing header fields
4.2. Compression Codings
The codings defined below can be used to compress the payload of a message.
4.2.1. Compress Coding
The "compress" coding is an adaptive Lempel-Ziv-Welch (LZW) coding [Welch] that is commonly produced by the UNIX file compression program "compress". A recipient SHOULD consider "x-compress" to be equivalent to "compress".
4.2.2. Deflate Coding
4.2.3. Gzip Coding
The "gzip" coding is an LZ77 coding with a 32-bit Cyclic Redundancy Check (CRC) that is commonly produced by the gzip file compression program [RFC1952]. A recipient SHOULD consider "x-gzip" to be equivalent to "gzip".
4.3. TE
The "TE" header field in a request indicates what transfer codings, besides chunked, the client is willing to accept in response, and whether or not the client is willing to accept trailer fields in a chunked transfer coding.
The TE field-value consists of a comma-separated list of transfer coding names, each allowing for optional parameters (as described in Section 4), and/or the keyword "trailers". A client MUST NOT send the chunked transfer coding name in TE; chunked is always acceptable for HTTP/1.1 recipients.
Three examples of TE use are below.
TE: deflate TE: TE: trailers, deflate;q=0.5
The presence of the keyword "trailers" indicates that the client is willing to accept trailer fields in a chunked transfer coding, as defined in Section 4.1.2, on behalf of itself and any downstream clients. For requests from an intermediary, this implies that either: (a) all downstream clients are willing to accept trailer fields in the forwarded response; or, (b) the intermediary will attempt to buffer the response on behalf of downstream recipients. Note that HTTP/1.1 does not define any means to limit the size of a chunked response such that an intermediary can be assured of buffering the entire response.
When multiple transfer codings are acceptable, the client MAY rank the codings by preference using a case-insensitive "q" parameter (similar to the qvalues used in content negotiation fields, Section 5.3.1 of [RFC7231]). The rank value is a real number in the range 0 through 1, where 0.001 is the least preferred and 1 is the most preferred; a value of 0 means "not acceptable".
If the TE field-value is empty or if no TE field is present, the only acceptable transfer coding is chunked. A message with no transfer coding is always acceptable.
Since the TE header field only applies to the immediate connection, a sender of TE MUST also send a "TE" connection option within the Connection header field (Section 6.1) in order to prevent the TE field from being forwarded by intermediaries that do not support its semantics.
4.4. Trailer
When a message includes a message body encoded with the chunked transfer coding and the sender desires to send metadata in the form of trailer fields at the end of the message, the sender SHOULD generate a Trailer header field before the message body to indicate which fields will be present in the trailers. This allows the recipient to prepare for receipt of that metadata before it starts processing the body, which is useful if the message is being streamed and the recipient wishes to confirm an integrity check on the fly.
Trailer = 1#field-name
5. Message Routing
HTTP request message routing is determined by each client based on the target resource, the client's proxy configuration, and establishment or reuse of an inbound connection. The corresponding response routing follows the same connection chain back to the client.
5.1. Identifying a Target Resource
HTTP is used in a wide variety of applications, ranging from general-purpose computers to home appliances. In some cases, communication options are hard-coded in a client's configuration. However, most HTTP clients rely on the same resource identification mechanism and configuration techniques as general-purpose Web browsers.
HTTP communication is initiated by a user agent for some purpose. The purpose is a combination of request semantics, which are defined in [RFC7231], and a target resource upon which to apply those semantics. A URI reference (Section 2.7) is typically used as an identifier for the "target resource", which a user agent would resolve to its absolute form in order to obtain the "target URI". The target URI excludes the reference's fragment component, if any, since fragment identifiers are reserved for client-side processing ([RFC3986], Section 3.5).
5.2. Connecting Inbound
Once the target URI is determined, a client needs to decide whether a network request is necessary to accomplish the desired semantics and, if so, where that request is to be directed.
If the client has a cache [RFC7234] and the request can be satisfied by it, then the request is usually directed there first.
If the request is not satisfied by a cache, then a typical client will check its configuration to determine whether a proxy is to be used to satisfy the request. Proxy configuration is implementation-dependent, but is often based on URI prefix matching, selective authority matching, or both, and the proxy itself is usually identified by an "http" or "https" URI. If a proxy is applicable, the client connects inbound by establishing (or reusing) a connection to that proxy.
If no proxy is applicable, a typical client will invoke a handler routine, usually specific to the target URI's scheme, to connect directly to an authority for the target resource. How that is accomplished is dependent on the target URI scheme and defined by its associated specification, similar to how this specification defines origin server access for resolution of the "http" (Section 2.7.1) and "https" (Section 2.7.2) schemes.
HTTP requirements regarding connection management are defined in Section 6.
5.3. Request Target
Once an inbound connection is obtained, the client sends an HTTP request message (Section 3) with a request-target derived from the target URI. There are four distinct formats for the request-target, depending on both the method being requested and whether the request is to a proxy.
5.3.1. origin-form
The most common form of request-target is the origin-form.
origin-form = absolute-path [ "?" query ]
When making a request directly to an origin server, other than a CONNECT or server-wide OPTIONS request (as detailed below), a client MUST send only the absolute path and query components of the target URI as the request-target. If the target URI's path component is empty, the client MUST send "/" as the path within the origin-form of request-target. A Host header field is also sent, as defined in Section 5.4.
For example, a client wishing to retrieve a representation of the resource identified as
http://www.example.org/where?q=now
directly from the origin server would open (or reuse) a TCP connection to port 80 of the host "www.example.org" and send the lines:
GET /where?q=now HTTP/1.1 Host: www.example.org
followed by the remainder of the request message.
5.3.2. absolute-form
When making a request to a proxy, other than a CONNECT or server-wide OPTIONS request (as detailed below), a client MUST send the target URI in absolute-form as the request-target.
The proxy is requested to either service that request from a valid cache, if possible, or make the same request on the client's behalf to either the next inbound proxy server or directly to the origin server indicated by the request-target. Requirements on such "forwarding" of messages are defined in Section 5.7.
An example absolute-form of request-line would be:
GET http://www.example.org/pub/WWW/TheProject.html HTTP/1.1
To allow for transition to the absolute-form for all requests in some future version of HTTP, a server MUST accept the absolute-form in requests, even though HTTP/1.1 clients will only send them in requests to proxies.